Checking Lawn Mower Blades

How to Stop a Mower Scalping Bare Strips and Cutting Uneven by Measuring the Real Blade Height (Instead of Trusting the Wheel Notches)

  • The notch on a mower’s height lever only hints at a height, so the only way to know the real blade height is to measure it.
  • Setting every wheel to the same notch and measuring again is the first fix to try for a scalped strip or an uneven cut, and it costs nothing.
  • A light coat of lubricant on the wheel adjusters before winter helps prevent rust and keeps them moving smoothly, so the height stays where you set it.

Why Your Mower Scalps Bare Strips When the Lever Says the Height Is Right

You set the lever. You mowed a straight line. Behind you lies a pale, bare strip along one side, and the rest of the lawn looks patchy, with some grass cut short and some left standing. It is easy to blame the blade or the grass. Start with the lever.

The fix takes a flat floor, a ruler and a little patience. Make the mower safe, then measure from the bottom edge of the blade to the floor. Set every wheel to the same notch and measure again. Finish by cleaning and lightly oiling the wheel adjusters so they do not seize in the shed over winter.

Here is the fact that catches people out. Consumer Reports notes that most manufacturers ship mowers from the factory with the deck in its lowest position, often as low as 1.5 inches (3.8 cm), and that this setting can scalp a lawn in perfect weather. If you never touched the lever, or touched it once and trusted the notch, your mower could be cutting lower than you think.

What a Scalped or Uneven Cut Is Telling You

A scalped strip and a ragged, uneven finish look like two problems. They share one root: the blade is not where you believe it is.

Think about how the cut happens. The blade spins in a flat disc under the deck, and the deck rides on the wheels. If one side of the deck sits a notch lower than the other, the whole disc tilts. The low side digs in and shaves the grass to the soil. The high side only skims the tips. One pass leaves a bare stripe beside a ragged stripe, and the mower did exactly what its wheels told it to do.

The RHS lists what else scalps a lawn and leaves bare patches: soft ground where the wheels sink in, turns taken too fast, ruts from cutting in the same direction every time, a height of cut that is too low, and a surface with bumps and hollows. Rule these out before you blame the mower. A sunken wheel or a fast turn tips the deck for a moment, exactly as a low notch does. Ruts have the same effect over several mows. Roger Cook, the contractor on This Old House, explains how they form: “I like to change the pattern. I’m mowing every week because if you mow the same way every week you can actually leave ruts in the lawn from the wheels.”

Look at where the damage sits. A bare strip in the same place on every mow suggests a wheel setting. A bare patch on a bump or over a tree root points to the ground. The RHS warns that extremely low cutting scalps the lawn where bumps or tree roots sit at the surface. Wheels that stray into a flower bed or off a hard edge do it too, so leave a small margin uncut and finish the edge with a string trimmer.

The RHS warns that close mowing weakens the grass plants, encourages shallow rooting and leaves the lawn more susceptible to drought damage, weeds and moss, so a mower that cuts too low is worth fixing early.

How to Measure the Real Blade Height and Set Every Wheel

Work on a level surface, such as a driveway or a garage floor. A sloping lawn gives a false reading.

Make the mower safe first. On a battery mower, remove the battery and the safety key. On a gas mower, detach the spark plug wire from the spark plug, typically on the front of the mower. Pulling it off takes a little effort. “The wire is insulated by a rubber casing and takes some wiggling to get off,” says John Galeotafiore, head of Consumer Reports’ home improvement testing. “But it’s not that hard to do, and the wire and its casing reattach easily to the spark plug.”

Now lift the side or rear discharge flap, the cover over the opening where cut grass leaves the deck. The blade sits behind it. Hold a ruler or tape measure upright on the floor beside the blade and read the distance from the floor to the bottom edge of the blade. Write it down in centimetres and inches.

Next, look at the levers. Walk-behind mowers can have one lever for each wheel, one lever for the rear wheels and another for the front, or a single lever for all four wheels. On a riding mower, one lever raises and lowers the deck independently of the wheels. Where there are several levers, move them one at a time and set each to the same notch as its neighbour.

Measure again after every change. Do not trust the notch to give you the number, as notches do not always match a cutting height. If the blade reads the same at the front and back of the deck, the deck is level. If it does not, a wheel is still out. Reconnect the plug lead or battery only when you have finished.

Want a different height? Our piece on the height to leave it at before winter covers that choice. This one stays with the setting. Whatever height you pick, avoid excessively close mowing.

Why the Notches Lie and the Wheels Drift

The notch is a mark on a plastic or metal plate. The blade height is the result of the notch, the wheel size, the tyre pressure and how the deck sits on its wheels. A little wear or a nudged lever and the two part company.

Several things cause the drift. This Old House says to lubricate the wheel adjustment mechanisms to prevent rust and keep them working smoothly, which suggests a seized lever is a common cause. A soft tyre drops one corner of the deck. A worn wheel is smaller than its partner, so it sits lower. That is why the This Old House checklist for uneven cutting starts with all the wheels at the same height, then asks whether the deck is clean and the blade is damaged or dull. Its wheel check adds three jobs: set tyre pressure, look for wheel wear and tighten the wheel nuts.

The tilted disc explains why every wheel must match. A mower with three wheels at one setting and one at another does not cut at either height. It cuts at a slant.

If a wheel is worn flat on one side or wobbles on its axle, no lever setting will cure it. Our guide to a new belt or wheels shows how to judge the wear and which parts you can swap yourself.

How to Clean and Oil the Adjusters and the Deck

A mower set to the right height will drift again if its adjusters are gummed up with grass, grit and rust. A rag and a can of spray lubricant stop that.

Start with the deck. Clippings stick to the underside, especially on a damp lawn. Once the clumps get bad they restrict airflow inside the deck and the cut suffers. Dried clippings are a pain to remove, so clean the deck after each mow. Some mowers have a washout port for a hose, and a plain rag also works. Wear heavy gloves to protect your hands from the blade, and take out the spark plug wire or safety key each time.

For a stuck-on layer, Roger Cook recommends a hands-on job: “Take the blade off, take a putty knife and scrape the deck clean.” A wire brush clears what remains, and then he sprays the underside with a lubricant. “That’s gonna make it slick so that no grass is gonna stick in there anymore,” Roger explains. A second option is a coat of silicone spray, sold at home centres and hardware stores, on the cleaned, dry deck to slow the next build-up. For the full job, see how to clean caked grass under the deck.

Then the adjusters. Lubricate the wheel adjustment mechanisms to prevent rust and keep them moving smoothly. Spray a light coat on both wheel axles and lubricate the control cables as your manual says. Light means light. Wipe the levers and tracks clean first, spray a thin film, work each lever through its full travel a few times and wipe off the extra. Excess oil collects grit.

November is a good month for this job, before the mower goes into the shed for winter.

How to Stop It Coming Back and When to Give Up and Call Someone

Make measuring a habit. Check the real blade height at the start of the season, after any adjustment and after any knock to the wheels. Set the levers to the same notch every time, so a fault shows up fast. Clean the deck after each mow.

Match your mowing to the ground. Vary the direction of cut so ruts do not form, take turns slowly and keep the wheels off soft ground. Level bumps and hollows rather than scalping over them.

Know when the lever is not the problem. If the mower vibrates excessively, stop and check the blade and the crankshaft. A bent crankshaft can lead to uneven cutting and potential engine damage, and it needs replacing, which is a job for a small-engine repair shop. A damaged blade needs balancing or replacing too. If the cut stays uneven after every wheel matches, the deck is clean and the blade is sound, stop mowing and have the mower looked at before the engine takes the strain.

Otherwise a ruler, a flat floor and a can of lubricant are all the repair this problem asks for.

George Howson

Written by

George Howson

George Howson is the founder of Lawn and Mowers and has spent over a decade maintaining and improving gardens across the UK. He is the first person his family and friends turn to for lawn and garden advice, and is an active member of a local community gardening group. George started this site to share practical, no-nonsense guidance with everyday gardeners who want real results without the guesswork.

More articles by George Howson →

Leave a Reply

Your email address will not be published. Required fields are marked *


The reCAPTCHA verification period has expired. Please reload the page.